- Other Fluke companies:
- Fluke
- Fluke Biomedical
- Fluke Networks
- Fluke Process Instruments
See more Fluke brands
Support for your most demanding ac traceability requirements
The 792A is an ultra-high accuracy AC/DC Thermal Transfer Standard, designed to meet the most demanding ac traceability requirements. Using the patented Fluke Calibration RMS sensor and thin film range resistors, the 792A offers an extraordinary transfer accuracy, with total uncertainties of as low as ±10 ppm (±5 ppm from the National Institute of Standards and Technology or NIST). The 792A also provides a wide voltage range of 2 mV to 1000V, and a wide frequency range of 10 Hz to 1 MHz.
The Fluke Calibration solid-state RMS sensor also provides the 792A with remarkable temperature stability and fast settling time. Now you can be ready to make measurements in 30 seconds instead of 30 minutes. To simplify the transfer process, the 792A's 2V output permits you to use a high-resolution digital multimeter rather than a null meter.
The 792A is designed to support the calibration of the most accurate ac instruments in your standards lab workload, including calibrators like the Fluke Calibration 5700A/5720A, voltmeters like the Fluke Calibration 8506A or the HP 3458A, and ac measurement standards like the Fluke Calibration 5790A.
The 792A consists of four units. The Transfer Unit is the main analog component of the 792A for the 20 mV to 220V ranges. Stainless Steel Type-N connectors assure low signal loss and high measurement repeatability. The separate Power Pack unit permits the Transfer Unit and 1000V Range Resistor to be shipped independently for calibration. The 1000V Range Resistor isolates the heat generated at high voltages outside the main Transfer Unit. The Range Resistor has a low temperature coefficient, stabilizes quickly and exhibits small ac/dc differences. The Transfer Switch provides for switching between the ac and dc inputs.
Each 792A is shipped from the factory traceable to national standards. Each 792A also includes a table of correction factors and uncertainties for measured ac/dc differences.
A40 and A40A support ac current transfer measurements. An optional 792A-7004 Adapter is required.
- Accurate, fast and easy to use
- Fully traceable performance
- Nine ranges from 22 mV to 1000V (with external range resistor)
- Visual and audible alert warns of approaching overload condition
- Input connector located on rear panel
- Two volt (full scale) output permits the use of a high resolution digital multimeter to simplify transfer measurements
- External power supply makes bench use more convenient and simplifies shipping of the transfer unit for calibration
Accurate, fast and easy to use
At the heart of the 792A is the patented Solid-State Thermal RMS sensor, which has been proven in a variety of Fluke Calibration products since 1979. Its output voltage is 2V, compared to the 7 to 10 mV output of traditional thermocouples. That means the 792A exhibits excellent signal-to-noise characteristics and minimal reversal errors as low as 10 ppm relative to input voltage. The 2V output also permits you to make measurements with high resolution so you can use a digital voltmeter rather than a null meter to make transfers. Not only are measurements easier to make, they are more precise as well. And because it is small, the RMS Sensor has very low thermal mass, so the 792A stabilizes in as little as 30 seconds and can be used over a wide temperature range of 11° C to 35° C. The RMS Sensor is designed to be rugged and reliable. Each is built to exacting standards by the Fluke Microelectronics Operation to maintain quality and consistency, part after part.
Fully traceable performance
Each 792A is shipped from Fluke Calibration with a certificate of calibration. Included is a table of correction factors and uncertainties for measured ac/dc differences.
To support the traceability requirements for an instrument as accurate as the 792A, the Fluke Calibration Metrology Department developed a unique system to transfer national laboratory values to the 792A production environment. This system is based on proven techniques developed to maintain a 732A direct voltage standard to within a few parts in 100 million. Statistical treatment of data resulting from successive intercomparisons of virtually identical 792As is used to minimize transfer uncertainties. To achieve even higher performance, you can have the transfer uncertainties of your 792A assigned directly by any national standards organization.
Periodic calibration and recertification is available from Fluke Calibration. This service repeats the original calibration procedure. A new table of correction factors and uncertainties for measured ac/dc differences is returned with your instrument. Order 792A-000.
| General Specifications | |||||||||
| AC-DC Difference |
|
||||||||
| Temperature Stabilization |
|
||||||||
| Warm up Time |
|
||||||||
| Temperature Performance |
|
||||||||
| Relative Humidity |
|
||||||||
| Altitude |
|
||||||||
| Input Low Isolation |
|
||||||||
| Guard Isolation |
|
||||||||
| EMI/RFI |
|
||||||||
| Line Power |
|
||||||||
| Calibration Documentation |
|
||||||||
| Size |
|
||||||||
| Weight |
|
||||||||
| Accessory | Description |
|---|---|
| 5440A-7002 |
Low Thermal Test Leads |
| 5440A-7003 |
Low Thermal Copper EMF Plug-In Cables, Spade Connectors |
| 792A-7001 |
Power Pack |
| 792A-7002 |
1000V Range Resistor |
| 792A-7003 |
Transfer Switch |
| Priority Gold Instrument CarePlan |
Fluke Calibration Priority Gold Instrument CarePlans are available for most calibration products. Please contact your local Fluke Calibration sales representative for details or to request a quote. You may also call the Customer Care Center at 800-882-6153 or send email to premiumcare@fluke.com. |
| Product Manuals |
|---|
792A Instruction Manual (English) (12.88 MB) |
|
792A Instruction Manual Supplement (35.93 KB) |
|
792A Statement of Memory Volatility
(32.27 KB) |
| Data Sheets |
|---|
|
792A AC/DC Transfer Standard Data Sheet (2.24 MB) |
|
792A AC/DC トランスファー標準器データシート (120.07 KB) |
| Papers / Articles |
|---|
|
Calibrating Precision Multimeters Using a Characterized Multifunction Calibrator (268.09 KB) |
|
使用多功能校准器特性修正技术校准高精度数字多用表 (1.4 MB) |